MESHFORGE Browser CAD Lab · Binary STL & Laser DXF
ENGINEERING GUIDE · KERF CHART

Laser Kerf Reference Chart & Joint Fit Calibration Guide

Measure true beam kerf on Glowforge, xTool diode, and CO2 lasers and test press-fit vs. glue-fit finger joints directly in our live parametric box studio.

100% Local Processing · Zero Uploads
Viewport Shader
Drag to orbit 360° · Scroll to zoom
Red #FF0000 · Laser Cut Blue #0066FF · Engrave Labels
Cut Sheet: -- Fingers X/Y/Z: --
ISO 18004 Matrix: --
Drag to orbit 360° · Scroll to zoom
Pause for Filament Color Swap at Z = 2.20 mm
Landed Unit Cost $0.00
Break-Even Price $0.00
Suggested Wholesale $0.00
Suggested Retail $0.00
Net Profit / Unit $0.00
Machine Profit / Hr $0.00/h

Unit Cost Waterfall Breakdown

Filament / Resin Material $0.00
Electricity Consumption $0.00
Printer Depreciation & Maintenance $0.00
Post-Processing & QC Labor $0.00
Failure Rate Risk Buffer $0.00
Packaging & Hardware $0.00
Marketplace & Payment Fees $0.00

Production Batch Economics

Batch Qty Unit Cost Total Cost Gross Revenue Net Profit Machine Hrs
ENGINE Laser Box
TRIANGLES --
STL SIZE --
BOUNDING BOX --
EST. PRINT --

Maker Engineering Workflow

1. Cut a 10-Strip Kerf Gauge

Cut ten 10.00 mm wide strips side-by-side from your target sheet, push them flush together, and measure total stack width with digital calipers.

2. Calculate Exact Kerf Formula

Compute Kerf = (100.00 mm − Measured Stack Width) ÷ 10. Expect 0.11–0.14 mm on diodes and 0.14–0.20 mm on CO2 lasers.

3. Dial Into MeshForge Laser Box

Plug your measured kerf into our parametric box generator above and verify tight zero-wobble finger joints on the very first cut.

Laser Kerf Compensation Reference Chart (CO2 & Diode)

Laser MachineMaterial & ThicknessMeasured KerfTypical Speed / PowerJoint Fit Guidance
Glowforge Basic / Pro (40W CO2)3mm Baltic Birch Plywood0.15 mm170 / FullTight press-fit; no glue needed on small boxes
Glowforge Basic / Pro (40W CO2)3mm Cast Acrylic0.16 mm165 / FullUse 0.14 mm for slip-fit solvent welding (Weld-On)
xTool S1 / D1 Pro (20W Diode)3mm Basswood / Birch0.12 mm8 mm/s · 100%Fine rectangular diode spot; air assist mandatory
xTool P2 (55W CO2)4mm MDF / Draftboard0.18 mm16 mm/s · 90%Wipe charred edges before dry-fitting finger joints
OMTech K40 / 60W CO26mm Baltic Plywood0.20 mm9 mm/s · 75%Use 2-inch focal lens to minimize tapered kerf walls

Why Kerf Changes With Focal Length, Material Density & Speed

Laser kerf is the physical width of material vaporized by the focused beam. Because laser beams form an hourglass waist, thicker sheets (6 mm plywood) exhibit slightly wider average kerf and slight taper compared to thin 3 mm basswood. Slower cutting speeds or overly high power dump extra heat into edges, widening wood char and expanding effective kerf by 0.03–0.05 mm.

For dry-fit boxes that assemble with light rubber-mallet pressure and zero glue, enter 100% of your measured kerf. For acrylic solvent welding or quick wood-glue assembly, reduce kerf compensation by 0.02 mm so joints slip smoothly without splitting veneers.

CAD & Fabrication Modules

Quick-Start Maker Presets

Technical FAQ

What happens if I set laser kerf compensation too high?

Excessive kerf widens tabs too aggressively, causing finger joints to refuse insertion or crack brittle cast acrylic and thin plywood outer plies when tapped together.

Does a 20W diode laser have a different kerf on X vs. Y axis?

Many multi-emitter diode lasers have a slightly rectangular focal spot (e.g. 0.08 × 0.10 mm). Average your X and Y kerf strip readings for balanced box assembly.

Does kerf compensation alter the final exterior size of my box?

No! MeshForge shifts the cut contour outward by exactly +kerf/2, which means the vaporized beam radius removes that exact allowance and leaves final outer dimensions accurate to ±0.05 mm.